I have a Godox XPro transmitter (Nikon) which works fine with my AD200PRO
I also have another pair of transmitter and receiver units (Calumet) dedicated for Nikon use.
I thought that given both the Godox and Calumet use the same frequency - 2.4GHz - I could use the XPro to fire the Calumet receiver attached to another flash (in this case a Metz 44).
However, this doesn't seem to work. Am I doing something wrong? Is my assumption wrong or do you have to use Godox dedicated receivers to fire flashes?
Thanks in advance.
Is this off camera flash theory correct?
-
- Posts: 183
- Joined: Fri 05 Jul 2019, 18:47
-
- Posts: 7316
- Joined: Tue 11 Sep 2012, 16:38
- Contact:
Re: Is this off camera flash theory correct?
abennettphotography wrote:I thought that given both the Godox and Calumet use the same frequency - 2.4GHz - I could use the XPro to fire the Calumet receiver attached to another flash (in this case a Metz 44).
These devices usually have a function to configure separate channels. It is there so that if two people are shooting near each other, they will not trigger the other's flash. Check that the Calumet receiver is set to the same value as the Godox.
Do let us know how you get on.
-
- Posts: 183
- Joined: Fri 05 Jul 2019, 18:47
Re: Is this off camera flash theory correct?
Interesting. I assumed they were both on the same channel as I the Calumet's default setting is Group A, Channel 1 and I'm pretty sure I set teh Godox to that. But will check and give it a go.
-
- Posts: 183
- Joined: Fri 05 Jul 2019, 18:47
Re: Is this off camera flash theory correct?
Hmmm. So tried again and made sure all the channels and groups matched but still no joy. So either you can't mix and match or else I'm doing something wrong...
-
- Posts: 7316
- Joined: Tue 11 Sep 2012, 16:38
- Contact:
Re: Is this off camera flash theory correct?
[quote="abennettphotography"....either you can't mix and match or else I'm doing something wrong...[/quote]
Probably.
Without being familiar with the kit, it is difficult to give anything other than a general suggestion. Presumably you have already tried Google. Godox support, if such a thing exists, might be able to help. Calumet has long since been absorbed into Wex so they might not be in a position to assist. It is worth asking, though. A further possibility is incompatibility between the Calumet receiver and the Metz flash. Sometimes manufacturers cannot resist designing gear so that it only works with their own products. I have no idea whether that applies to Metz or Godox, though.
Probably.
![Wink ;)](./images/smilies/icon_e_wink.gif)
Without being familiar with the kit, it is difficult to give anything other than a general suggestion. Presumably you have already tried Google. Godox support, if such a thing exists, might be able to help. Calumet has long since been absorbed into Wex so they might not be in a position to assist. It is worth asking, though. A further possibility is incompatibility between the Calumet receiver and the Metz flash. Sometimes manufacturers cannot resist designing gear so that it only works with their own products. I have no idea whether that applies to Metz or Godox, though.
-
- Posts: 183
- Joined: Fri 05 Jul 2019, 18:47
Re: Is this off camera flash theory correct?
Thanks Mike. All good ideas. I will follow up.
-
- Posts: 183
- Joined: Fri 05 Jul 2019, 18:47
Re: Is this off camera flash theory correct?
So, theory flawed. Triggers and receivers have to be of the same brand to communicate with each other. This from Pixapro (Godox in this country):
"It doesn't work that way, unfortunately. The 2.4GHz signal is just the frequency that is used to transmit the instructions between one device and another. The two devices both need to be designed from the ground up to communicate with one another for them to be compatible (different manufacturers use different protocols for their own devices unless they have been specifically designed to work with another trigger system).
Our triggers are only compatible with other Pixapro/Godox triggers and receivers"
"It doesn't work that way, unfortunately. The 2.4GHz signal is just the frequency that is used to transmit the instructions between one device and another. The two devices both need to be designed from the ground up to communicate with one another for them to be compatible (different manufacturers use different protocols for their own devices unless they have been specifically designed to work with another trigger system).
Our triggers are only compatible with other Pixapro/Godox triggers and receivers"
Return to “Techniques & Tutorials”
Who is online
Users browsing this forum: No registered users and 1 guest